betting tips, daily bettingbetting tipsbetting tips, free betting

A hubless wheel from the past: The Black Hole

Concept, Road Bike 14 4789

As I mentioned in a recent post, hubless wheel concept bikes have been appearing on the web in droves lately.  Fast Company recently featured a few of those recent concept bikes (and one really old one) in their “Almost Genius” category, reserved for designs that don’t quite work. On the Core77 discussion boards, slippyfish recently started, “The Official Hubless Wheel Hater Thread”. One of the posts on that thread even points a pretty entertaining gallery of late 19th century hubless monocycles. Of course,  BSNYC’s “save the hubs” campaign gets a mention too.  All in all, it seems that everyone is kind of tired of seeing new hubless wheel concepts on the web every week.

What better time to revisit a couple of old posts about a hubless wheel, which (I believe) actually went into production for a short time in the mid 90s. The picture you see above is an early prototype of the Black Hole hubless wheel system from “Wear and Tear”.  According to the company, this assembly weighed about a pound less than a conventional fork and wheel. Sounds great…why didn’t it catch on?

To the left, you can see a later prototype of the Black Hole. Obviously, the designers were a little too optimistic with that large opening in the previous prototype. I am not sure what happened to Wear and Tear, but I have my doubts that this later prototype was lighter than the average conventional fork and wheel that was available at the time.

Update 3/17/10: Damon Rinard has better pictures of the Black Hole in his Flickr photostream.

On an unrelated note, the Taipei International Cycle Show opens tomorrow. As he did last year, Eric Stoddard will be writing a guest post or two from the show. I’m looking forward to reading what he has to say.

Related Posts


  1. Champs March 16, 2010 at 1:31 pm -  Reply

    With the UCI making the rules, that revised design would be on shaky ground, and the road would feel the same way in any sort of crosswind.

    • James T March 16, 2010 at 1:44 pm -  Reply

      Both of these prototypes pre-date the Lugano charter, so UCI regulations were not a concern at the time. The crosswind issue though was a still a concern before 1996…well, at least it should have been.

  2. micamb March 16, 2010 at 3:03 pm -  Reply

    I saw hubless concepts in the early 90’s and thought it would be ideal for placing the cranks on a recumbent. I wonder if the ‘concept’ would solve any problems today.

  3. Ross Nicholson March 16, 2010 at 9:15 pm -  Reply

    Hubless works only well with room temperature superconductor levitation, eh?

  4. Nick G March 17, 2010 at 6:23 pm -  Reply

    I love the look of hubless wheels, but have doubts about whether they’ll ever become close to practical. Some of the ideas floating around dream of magnets as bearings though. If magnets were used as bearings, I can imagine them being too weak for conventional hubs but strong enough on a setup like this…

    • art March 30, 2010 at 9:19 am -  Reply

      Regardless of whether balls or magnets are used as bearings, there are two fundamental limitations. First is trying to match the tight tolerances of a hub bearing on a diameter that’s ten times bigger. The second is that on a conventional wheel, even a full disc, the rim undergoes a significant amount of deformation under impact load. So unless those magnets have a gap of several millimeters, they will be damaged on the first pot hole.

  5. Rude dog July 25, 2011 at 1:58 pm -  Reply

    I actually used the Black Hole wheel in a graduate project that never went thru to final completion (hour record attempt…we lost funding). The wheel itself was actually pretty heavy, but once it got rolling it really, really was very fast. It was not ideal for the road. It was far better suited for the track. The biggest down fall with it was the fact that the bearings were not sealed very well. In fact if a little bit of road dirt got up into the race the wheel would tend to grind. I outfitted it onto my road bike and onto my track bike and rode it well. It was about 5 percent faster than a standard aero front wheel (yeah eliminating the spokes made that big of difference). Overall a very cool concept thta if they ever would have worked out the bugs with the bearing, would have been a game changer. The UCI ultimately did noot want to entertain the concept and banned wheels that mount as a single fork.

  6. onedirtyrider July 10, 2012 at 3:21 pm -  Reply

    The photo of the Zipp bicycle with the Black Hole is my bike. I rode many of the early prototypes. The reason that the back of the “hole” was filled in was not for stiffness, it was for aero stability. Imagine a line, straight down from the bottom of the headset (not on the angle of the fork) and you’ll find that 2/3rds of the wheel is in front of this line. That effected crosswind handling. By filling in the back portion, it acted as a rudder and was actually very easy to ride in most wind conditions. The wheel did actually see a small production run.

    • Adam Majoros August 3, 2015 at 3:58 am -  Reply

      I wonder where and how could I get more info to this wheel?
      I work on a hubless design, and it looks like one working unit.
      I wish to get the info this project collected back than.

Reply Cancel

Your email address will not be published. Required fields are marked *

Bicycle Design Merchandise=